
BS EN 343-2003+A1-2007 Protective clothing—Protection against rain(防护服-防雨防护服英国|欧洲标准)
National foreword
This British Standard is the UK implementation of EN
343:2003+A1:2007.
It supersedes BS EN 343:2003 which is withdrawn.
The start and finish of text introduced or altered by
amendment is indicated in
the text by tags. Tags indicating changes to CEN text
carry the number of the
CEN amendment. For example, text altered by CEN amendment
A1 is
indicated by !".
The UK participation in its preparation was entrusted by
Technical Committee
PH/3, Protective clothing, to Subcommittee PH/3/1,
Clothing for protection
against general hazards.
A list of organizations represented on this subcommittee
can be obtained on
request to its secretary.
This publication does not purport to include all the necessary
provisions of a
contract. Users are responsible for its correct
application.

Compliance with a British Standard cannot
confer immunity from
legal obligations.
Amendments/corrigenda issued since
publication
Date Comments
30 April 2008 Implementation of CEN amendment A1:2007
EUROPEAN STANDARD NORME
EUROPÉENNE
EUROPÄISCHE NORM
EN 343:2003+A1
August 2007
ICS 13.340.10 Supersedes
EN 343:2003
English Version
Protective clothing -
Protection against rain
Vêtements de protection
- Protection contre la pluie Schutzkleidung - Schutz gegen Regen
This European Standard
was approved by CEN on 2 July 2003 and includes Amendment 1 approved by CEN on
25 July 2007.
CEN members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions
for giving this European
Standard the status of a
national standard without any alteration. Up-to-date lists and bibliographical
references concerning such national
standards may be
obtained on application to the CEN Management Centre or to any CEN member.
This European Standard
exists in three official versions (English, French, German). A version in any
other language made by translation
under the responsibility
of a CEN member into its own language and notified to the CEN Management Centre
has the same status as the
official versions.
CEN members are the
national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland,
France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal,
Romania, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050
Brussels
© 2007 CEN All rights of
exploitation in any form and by any means reserved
worldwide for CEN
national Members.
Ref. No. EN
343:2003+A1:2007: E
1.Foreword
This document (EN
343:2003+A1:2007) has been prepared by Technical Committee CEN/TC 162
"Protective
clothing including hand
and arm protection and lifejackets", the secretariat of which is held by
DIN.
This European Standard
shall be given the status of a national standard, either by publication of an
identical
text or by endorsement,
at the latest by February 2008 and conflicting national standards shall be
withdrawn
at the latest by
February 2008.
This document includes
Amendment 1, approved by CEN on 2007-07-25.
This document supersedes
!EN 343:2003".
The start and finish of
text introduced or altered by amendment is indicated in the text by tags ! ".
This document has been
prepared under a mandate given to CEN by the European Commission and the
European Free Trade
Association, and supports essential requirements of EU Directive(s).
For relationship with EU
Directive(s), see informative Annex ZA, which is an integral part of this
document.
According to the
CEN/CENELEC Internal Regulations, the national standards organizations of the
following
countries are bound to
implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark,
Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia,
Lithuania, Luxembourg,
Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain,
Sweden, Switzerland and
United Kingdom.
BS EN 343:2003+A1:2007
2.Introduction
In this European
Standard the measured properties of materials and seams of protective clothing
and their
subsequent
classification are intended to ensure an adequate protection level. Water
proofness and water
vapour resistance are
the essential properties to be tested and marked on the label.
Water proofness is the
most important property and it is measured on material of the outer garment
layer. Tests
are made on new and
pretreated fabric samples and on parts with seams.
Some waterproof
materials are impermeable to water vapour transmission. However other materials
on the
market combine water
proofness with water vapour permeability. This property expressed by low water
vapour
resistance enhances
sweat evaporation and significantly contribute to body cooling. This is
valuable, because it
contributes to better
comfort and less physiological strain and prolongs the wearing time in certain
climatic
conditions (see annex
A).
BS EN 343:2003+A1:2007
3
3-1 Scope
This European Standard
specifies requirements and test methods applicable to materials and seams of
protective clothing
against the influence of precipitation (e. g. rain, snowflakes), fog and ground
humidity.
The testing of rain
proofness of ready made garments is excluded in this standard at this time
because a
separate test method for
such a property is currently being prepared.
3-2 Normative references
This European Standard
incorporates by dated or undated reference, provisions from other publications.
These
normative references are
cited at the appropriate places in the text and the publications are listed
hereafter. For
dated references,
subsequent amendments to or revisions of any of these publications apply to this
European
Standard only when
incorporated in it by amendment or revision. For undated references the latest
edition of the
publication referred to
applies (including amendments).
EN 340, Protective
clothing — General requirements
And so on……
BS EN 343:2003+A1:2007
4.Terms and definitions
For the purposes of this
European Standard, the following terms and definitions apply.
由于篇幅缘故,这里不便将关于BS EN 343-2003+A1-2007 Protective clothing—Protection against rain防雨防护服的英国/欧洲标准全文展现出来,耐戈友小编暂将简介内容概述如上,完整版本标准信息,请联系耐戈友网站客服索要。
下一篇:焊接防护服标准GB-15701-1995JZO 本文由耐戈友整理发布,转载请注明出处!
链接地址 http://www.negu.com.cn/?article-184.html

最近几年,ISO(国际标准化组织)在劳动防护用品方面颁布了许多新的标准。另外,德国、欧盟等标准化组织制定的标准,也逐步向ISO标准靠拢,ISO标准成为比较通用的标准。目前,在劳动防护用品方面,我国主要引用或者转化的外国标准也是ISO标准。据初步统计,ISO标准如下:
1)头部防护
ISO 3873:1977 工业用安全帽
2)眼面部防护
ISO 4007:1977 个人用护目镜词汇两种语言版
ISO 4849:1981 个人用护目镜技术要求
ISO 4850:1979 焊接和相关工艺的专用护目镜滤光镜应用和透射率的要求
ISO 4851:1979 个人用护目镜紫外线滤光镜应用和透射率的要求
ISO 4852:1978 个人用护目镜红外线滤光镜应用和透射率的要求
ISO 4854:1981 个人用护目镜光学性试验方法
ISO 4855:1981 个人用护目镜非光学性试验方法
ISO 4856:1982 个人用护目镜目镜和护目镜技术要求简表
ISO 6161:1981 个人用护目镜防激光辐射的滤光镜和护目镜
3)足部防护
ISO 2023:1994 橡胶鞋工业硫化橡胶衬里鞋规范
ISO 2251:1991 有衬里的抗静电橡胶靴规范
ISO 17249:2004 防链锯切割的安全鞋
ISO 20344:2004 个体防护装备鞋的测试方法
ISO 20345:2004 个体防护装备安全鞋
ISO 20346:2004 个体防护装备防护鞋
ISO 20347:2004 个体防护装备职业鞋
ISO 20344
cor.1:2005 个体防护装备
鞋的测试方法 勘误表
ISO 20345
cor.1:2005 个体防护装备
安全鞋 勘误表
ISO 20346
cor.1:2005 个体防护装备
防护鞋 勘误表
ISO 20347
cor.1:2005 个体防护装备
职业鞋 勘误表
4)躯干防护
ISO 2801:1998 阻热和隔热服防护服的选择、保存和使用的常用方法
ISO 6529:2001 防护服对化学品的防护 防液态和气态化学制品的抗渗透性的测试
ISO 6530:2005 防护服对液态化学品的防护 材料抗渗透性的测试
ISO 6942:2002 防护服阻热和隔热材料和材料部件受到辐射热源时的热性能评定
ISO 8194:1987 辐射防护辐射污染防护服设计、选择、检验和使用
ISO 9150:1988 防护服防熔融金属飞溅物性能测试 (GB/T 17599—1998 EQV)
ISO 9151:1995 阻燃隔热防护服有源条件下热传导性的测试法
ISO 9185:1990 防护服材料抗金属溶液穿透性的评定
耐戈友一直致力于安全知识的宣传和推广。结合十多年来生产国外高亮反光职业安全防护职业服装的成功经验,进行了深入的安全生产调查,按照国人的特点设计、制造适应国内市场消费的同类产品,并且所有产品均按照国际上对此类产品的具体标准来操作,推出了一系列的安全防护产品,提供给广大的职业人群,以最大程度的为他们的安全防护提供力所能及的保障。耐戈友的特种防护服之防静电服,全部使用进口面料生产制作,能有效的满足在此类环境下的防护需求。
下一篇:ISO有关劳动防护用品标准(下) 本文由耐戈友整理发布,转载请注明出处!

防静电工作服(简称“防静电服”)指为了防止衣服的静电积聚,用防静电织物为面料而缝制的工作服。关于防静电服的标准有国家标准GB12014-2009和欧盟标准EN1149。
一.国内防静电服标准GB12014-2009
1.国内防静电服标准GB12014-2009是由北京市劳动保护科学研究所起草,陕西元丰,西安精诚服装有限公司,总后军需研究所士兵中心参加起草的最新国家标准。适用于可能引起电击、火灾及爆炸危险场所穿的防静电服,不适用于抗电源电压。
2.防静电服一般是用普通纤维混纺导电纤维制成或嵌入导电长丝制成,一般是用涤纶长丝混合导电纤维制成。
3.相对于国外标准,国内标准抗静电性能主要是测试点对点电阻,而欧盟标准里测试项目比较多。
二.欧盟防静电服标准BS EN 1149
1. 欧盟防静电服标准BS EN 1149是由欧洲标准委员会发布,是测试防护服静电性能测试方法和要求的一系列标准。
2. 整个欧盟静电防护服测试方法标准分为4个部分,测量项目主要是静电性能,对于其他性能基本没有涉及。BS EN 1149-1是针对基于表面电阻的静电消散行为的大部分性能的测试方法,它确定的是短距离的电阻,不适用评估整件服装;BS EN 1149-2是测试材料电阻方法标准(回路电阻);BS EN 1149-3是测试电荷衰减方法标准;BS EN 1149-5规定了防护服抗静电材料性能及设计要求。
3. BS EN 1149标准相对国内标准测试项目比较多,而国内标准主要测试点对点电阻,比较简单。
4.由于防静电服标准主要关注的是服装的防静电性能,对于服装的阻燃性能没有要求,目前国内外的防静电服面料主要还是普通纤维纺导电纤维制成或嵌入导电长丝。
耐戈友一直致力于安全知识的宣传和推广。结合十多年来生产国外高亮反光职业安全防护职业服装的成功经验,进行了深入的安全生产调查,按照国人的特点设计、制造适应国内市场消费的同类产品,并且所有产品均按照国际上对此类产品的具体标准来操作,推出了一系列的安全防护产品,提供给广大的职业人群,以最大程度的为他们的安全防护提供力所能及的保障。耐戈友的特种防护服之防静电服,全部使用进口面料生产制作,能有效的满足在此类环境下的防护需求。
下一篇:ISO有关劳动防护用品标准(上) 本文由耐戈友整理发布,转载请注明出处!
相关文章:防静电工作服标准GB12014-2009 链接地址:http://www.negu.com.cn/?article-140.html